Jump to content

E36

Cristi B

By Cristi B
in Seria 3

 Share

Recommended Posts

Bavaria Newbie

Bavaria

Posted
Posted
Nu cred,Bavaria pare om de treaba,nu-i asa Bavaria? Hai spune cum se face :)

 

Voi nu aveti internet cu google? :lol:

 

Merge pe anumite modele de E36, mai noi.Dupa E36 merge pentru toate, E46, E90, etc.

 

"NOTE: Just for the hell of it. KLR means ignition switch position #1

(accessory) KL-15 is ignition switch position #2 (on), and KL-50 is ignition

position #3 (start)

 

This works on all instrument clusters 1992-1999 E36 - 4

door/coupe/convertible/M3.

 

Step 1. Press and hold the mileage reset button.

 

Step 2. Put key into ignition switch and turn to KLR (Ignition switch

position #1)

 

Your LCD display will show something like this "tESt 01"

 

Step 3. Once "tESt 01" is shown, let go of reset button and the IC

(Instrument Cluster) will go through

some test cycles. Numbers will be shown and here's what they mean:

 

1st display: BMW PART NUMBER (6 digits)

2nd display: CODE NUMBER (5 digits) Internal Coding Plug #

3rd display: K NUMBER (4 digits)

4th display: CHASSIS NUMBER (5 digits) this is part of your VIN

5th display: SOFTWARE VERSION (3 digits)

6th display: REVISION INDEX (2 digits) Hardware #

 

After all 6 displays are finished, an analog gauge test will be performed.

 

The self-test is canceled by switching the ignition off or to KL-15 (ignition

switch position 2)

 

 

 

IC (instrument cluster) tests 1-15

1995 - 1998 (99) 318ti

1996 - 2000? Z3

1997 - 1999 E36 4dr/coupe/convertible/M3

 

NOTE:

*Test functions 1-4 are unlocked tests and can be called up at any time for

display.

*Test functions 5-14 are locked and require unlocking the test mode before

they can be displayed.

*Test functions 2-14 can be selected at any time when the cluster is

unlocked, even when vehicle is moving.

*Test function 15 is the lock/unlock function.

 

Step 1: Press and hold the mileage reset button.

 

Step 2: Put key into ignition switch and turn to KLR (Ignition switch

position #1)

Your LCD display will show something like this "tESt 01"

 

Step 3: You will need to unlock the test function first so when the LCD

Display shows "tESt 01," press the reset button till you get to "tESt 15."

Once you're on test 15 press, and hold the reset button for a few seconds

until it displays "off." Now you can cycle through the test features. Here

they are as they follow:

 

Test 1: Instrument self test

 

Test 2: Engine Data - This display is an "engine factor" value that is stored

in the coding plug. The instrument cluster processor uses this factor in

addition to the "TD" signal from the DME control module to process and

display tachometer RPM based on the engine installed. For EXAMPLE:

*ENGINE FACTOR 2 = 4 CYLINDER

*ENGINE FACTOR 3 = 6 CYLINDER

*ENGINE FACTOR 4 = 8 CYLINDER

 

Test 3: SI elapsed distance - the total mileage in kilometer since the last

reset. Which service is due at the next inspection (OIL SERVICE or INSPECTION)

 

Test 4: SI elapsed days - no value for US vehicles. Relates to Euro annual

inspections.

 

Test 5: SI evaluation factor - for engine speed and temp. thresholds being

passed.

Display: n = 0 or 1. Engine speed (over-rev)

t = 0 or 1. Engine temp.

NOTE: "n0" means that you hit the maximum threshold for engine speed and "t1"

means you overheated the engine. I found out from my instructor that this

test 5 is false due to software related problems.

 

Test 6: Fuel Level and coolant temp. - Display of hexadecimal codes in

relation to gauge position.

Fuel gauge ----> Hex value

A (empty)---------> 0d

End of reserve---> 37

B-------------------> 54

C-------------------> 90

D------------------> c4

E (full)-----------> f0

 

Engine temp. ----- Hex Value

A----------------------> ce

B----------------------> 6d

C----------------------> 5c

D (center)----------> 4f-23

E-----------------------> 1e

F-----------------------> 18

 

Test 7: Engine speed (Digital Tach)- display of current engine speed

 

Test 8: Road speed - display of current road speed in km/h

 

Test 9 Distance reading - this allows the total stored mileage to be updated

if one of the storage components has to be replaced. This test step will be

used if the manipulation dot is illuminated in the cluster display. This

display will show the component with the lower mileage. For example:

Display of 012654 l indicates that the mileage in the internal EEPROM is

lower than the mileage stored in the coding plug.

Display of 000325 E indicates that the mileage in external coding plug is

lower then the total mileage stored in the internal EEPROM.

Pressing the reset button for 4 seconds will over write the lower mileage

with the higher mileage and cancel the manipulation dot. The SI data will

also be transferred at the same time.

 

Test 10: Status bits (input signals) - the status of digital inputs to the

cluster are displayed as 0 or 1.

Display: 0 = input low, 1 = input high.

_ _ _ _ _ _ <--- Mileage display...6 digits left to right

1st - belt contact, seat belt fastened = 0

2nd - ignition lock contact, key inserted = 0

3rd - door contact, door open = 0

4th - clock button pressed = 0

5th - SI reset = 0, for reset = 0

6th - EGS transmission failure = 0

 

Test 11: Status Bits (output signals) - the status of digital outputs is

displayed.

Display: 0 = output inactive, 1 = output active

_ _ _ _ _ _ <--- Mileage display...6 digits left to right

1st - Gong output

2nd - Brake warning lamp

3rd - Low fuel warning lamp

4th - EGA lamp

5th - seat belt lamp

6th - manipulation dot

 

Test 12: not used

 

Test 13: Country code of cluster - the display indicates the country version

of the cluster. This cannot be

changed in the workshop. Display: USA 02

 

Test 14: Software Reset - The reset must be carried out if any faults are

present that are not plausible before any components are replaced. After the

reset, the system will exit the TEST mode and the lock

will be reactived.

 

Test 15: lock/unlock"

Link to comment
Share on other sites
iulisv Newbie

iulisv

Posted
Posted

Cum se face:

-se apasa butonul de resetare km

-se pune contactul in pozitia 1 tinand in continuare apasat butonul

-se parcurge meniul pana la pozitia 15 si se deblocheaza tinand apasat mai lung(15on->15off)

-dupa ce s-a deblocat parcurgeti iar pana la pozitia 07 din meniu

-porniti motorul si gata.

Link to comment
Share on other sites
Fan de mic Newbie

Fan de mic

Posted
Posted

Asa d-nu IULI.Eu nu intelesesem cum se activeaza,si dezactiveaza :)

Da'e destul de simplu...tii apasat...bagi cheia...mergi pana la 15...activezi tinand apasat 15 sec...apoi eu asi vrea sa vad viteza afisata acolo :lol: parca la 8 era.

Abia astept sa incerc si eu :)

P.S:Sper sa mearga...ca matza mea e din 05/95.

Link to comment
Share on other sites
iulisv Newbie

iulisv

Posted
Posted
Asa d-nu IULI.Eu nu intelesesem cum se activeaza,si dezactiveaza :)

Da'e destul de simplu...tii apasat...bagi cheia...mergi pana la 15...activezi tinand apasat 15 sec...apoi eu asi vrea sa vad viteza afisata acolo :lol: parca la 8 era.

Abia astept sa incerc si eu :)

P.S:Sper sa mearga...ca matza mea e din 05/95.

Da, viteza e la pozitia 08.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
×
 Share
Go to topic listing

  • Recently Browsing   0 members

    • No registered users viewing this page.
×
×
  • Create New...

Important Information

Prin folosirea acestui site, sunteti de acord cu Terms of Use. Gasiti aici Guidelines. Politica de cookies: We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.